Passing Turkey Point at 3 pm. We're only 20 minutes behind schedule...had quite a bit of adverse current some of the time coming up the Bay.
This is a site to record our adventures aboard Owl Moon.
Tuesday, July 10, 2018
Heading North
We just left Annapolis. Off the dock a little after 8 am. We took some time doing circles off Tecumseh to calibrate the wind vane. It has been off for over a year now and I thought it would be nice to have it fixed. We also slowed at the harbor entrance to pull the speedo and clean it because it was not working. So, probably underway about 8:20.
![]() |
| Pulling away from Tecumseh marina. |
![]() |
| See you later, Annapolis. |
![]() |
| A strong 1.5 knot current against us as we motor up to the Bay Bridge. |
Friday, June 23, 2017
New Anchor
![]() |
| Anchor in place on Owl Moon |
![]() |
| Shackle pin held in place with seizing wire (learned this is called mouse the shackle) |
Monday, June 19, 2017
Father's Day Sail
![]() |
| John was at the helm (not really driving...the autopilot was) |
![]() |
| While Joe, Diane, and Tracy enjoyed the ride from the cabin top...changing sides with each tack. |
![]() |
| Eve-Marie and Sarah were back in the cockpit with me. |
![]() |
| Couldn't have had a better photo if it had been staged! |
![]() |
| We eventually started overtaking the photo boat to windward and he took some more photos of Owl Moon. |
Monday, April 10, 2017
Fast Ride Home to Annapolis
John had made sure Owl Moon was ready to go on previous trips to Regent Point. Sunday, Diane and John drove down to RP with two friends who were joining us on the sail north, Rick O'Donnel and Erin Harrington. We arrived RP in plenty of time to make final preparations for departure...installing jack lines, confirming that water tanks were full, stowing provisions and personal gear. We finished prep just in time to drive to the other side of the creek for dinner at Merroir.
We departed RP in the dark at 5 am, using the spotlight to find the daymarkers as we made our way out Locklies Creek. We also had the GPS track left on our way in to follow out. We took it slow and easy since the channel is very narrow and not very deep, going forward at engine idle speed.
Once we reached Windmill Point and turned north, our speed dropped considerably as the wind had gone light and we were now heading dead downwind...not what had been forecast. John reluctantly started the motor so that we could continue to make good time toward Annapolis. After about an hour of motoring, we we tried sailing for a bit, but there just wasn't enough wind to keep our speed over 4 knots. After about 30 minutes of slow progress north, we returned to motoring.
We arrived at our dock at 8 pm...15 hours to go the 96 miles from Regent Point.
![]() |
| Merroir provided blankets for customers to keep warm as the air chilled after sunset. |
Once in the Rappahannock River we were able to hoist sail as there was a fresh breeze from the south. We were able to sail on a reach out of the Rappahannock with our speed ranging from 6.5 to 7 knots. We only put out the small jib, figuring it would be easier to roll in as we jibed at Windmill Point to head north.
![]() |
| Sailing out of the Rappahannock just before sunrise with the moon setting behind us. |
Introducing the crew...Sunrise at the mouth of the Rappahannock.
Still motoring at lunch time, Diane made us all tuna melts for lunch. During lunch, the wind came up and once lunch was finished we briefly turned south to raise the mainsail. This was just north of Point No Point...we had motored across the entire mouth of the Potomac. Returning to our course to Annapolis once the mainsail was up, the wind was still dead downwind so we poled out the big jib to starboard and flew the little inside jib to port.
The wind built and we started making great time towards Annapolis.
![]() |
| Sailing Again! |
![]() |
| Happy to be sailing after a delicious lunch! |
Wing and wing up the Bay!
![]() |
| Photo op on the bow. |
![]() |
| Enjoying the day on the Bay! |
![]() |
| The sun was setting as we rounded Tolly Point and headed into the mouth of the Severn. |
![]() |
| Removing jack lines and getting fenders and docklines on deck in preparation for arrival. |
| Our track to Annapolis...a very straight course due to the south wind. |
Sunday, April 9, 2017
Upgraded to a new mainsheet that fits.
The 9/16" Sta-Set mainsheet that came with the boat is too big for the rope clutch...you have to pull it through and it leaves blue fuzzies (bits of polyester) behind. We upgraded to 7/16" Samson Ropes MLX. To save some money, we went down to 90' instead of the 100' that is the length of the original...the 90' is plenty. This line, with a Dyneema core, has a similar load rating to the thicker polyester core Sta-Set. A side benefit is that it won't twist so much between blocks and, when coiled, is a much smaller and lighter coil.
![]() |
| New mainsheet on top, old mainsheet on bottom. |
Tuesday, March 21, 2017
Unshimming the Board
We've haven't been able to get much use out of the centerboard since purchasing Owl Moon. The centerboard and slot has been cleaned and painted twice now. The problem we have had is it gets jammed up and won't deploy, even when motionless at the dock. The couple of times we were able to use it, we had to almost stop the boat head to wind to get it to lower. Paul thinks we need to remove the starboard shim at the top corner of the board where the pennant connects to the board. It is for stabilizing the board in the slot, but may be just a bit to thick.
The shim was removed by lowering the board all the way and then using a sawzall along the edge of the board to cut the fasteners which held the starboard to the centerboard. Now there is a bit of wobble in the board, but it will stabilize once it is loaded with water pressure under load.
The shim was removed by lowering the board all the way and then using a sawzall along the edge of the board to cut the fasteners which held the starboard to the centerboard. Now there is a bit of wobble in the board, but it will stabilize once it is loaded with water pressure under load.
![]() |
| Here the centerboard is lowered and the shim is just inside the centerboard slot ready for the sawzall. |
![]() |
| Shim successfully removed. |
![]() |
| Starboard shim with the two screw heads showing which had attached it to the centerboard. |
Subscribe to:
Posts (Atom)

























